Assembly Language Programming Jobs Remote Jobs in Usa

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Integral Fuel Cell Assembly (In- Tank Mechanic) to join our Join and Installation team in Everett and Renton, Washington. 

As an Integral Fuel Cell Assembly (In-Tank Mechanic), you will play a vital role in ensuring the highest standards of quality and safety while working within the confined spaces of aircraft fuel tanks. This position requires assembling and installing structural components, systems, and sub-assemblies to meet stringent quality requirements. You will be responsible for verifying kitted parts, performing drilling, riveting, and bonding, as well as assembling plumbing and electrical systems within the tank. Your attention to detail will be crucial as you conduct continuity checks, perform necessary rework, and ensure that all installations comply with specifications. Please note that this role involves working in tight spaces, including entering the wing through a approximately 9.5" x 17.7" opening; therefore, comfort with confined spaces is essential for success in this position.  

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation. 

Position Responsibilities: 

• Assemble and install parts, structural components, systems, and sub-assemblies to meet quality requirements for wing and horizontal stabilizer assemblies. 

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings. 

• Locate work areas using drawings, installation plans, or other paperwork that specifies airplane and section numbers. 

• Obtain and verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects. 

• Retrieve parts from the Parts Control Area or other designated locations if they are not pre-picked, ensuring they meet specifications. 

• Obtain a two-way radio and confined space flag before working in confined spaces, adhering to Communications System for Confined Hazardous Areas (CSCHA) rules and regulations. 

• Perform drilling, reaming, riveting, cold working, bonding, grounding, and sealing as necessary to complete work assignments. 

• Assemble and install aircraft plumbing and electrical systems within closed areas of the wing and horizontal stabilizer, ensuring compliance with specifications. 

• Perform pickup and rework, incorporating changes and conducting functional checks on work typically installed by lower classifications. 

• Perform continuity checks for electrical systems and hand form electrical wiring and soldering as necessary for work assignments.

• Perform final cleaning and closing of fuel cells, including vacuuming and installing fuel cell doors. 

• Locate and pre-install routing and clamping hardware for in-wing fuel tank electrical and plumbing systems as required. 

• Use precision measuring instruments to verify that quality standards are achieved. 

• Report job handicaps, such as errors in sequencing, parts, materials, and assembly procedures, following shop procedures. 

• Check work after completion of each operation to ensure assembly is complete and free of defects and remove and replace installations and related components as necessary. 

Physical Demands and Potential Hazards: 

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs. 

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting. 

• Work in environments that may involve contact with metals, solvents, and coolants. 

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards. 

• Adapt to varying noise levels and atmospheric conditions. 

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options. 

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee 

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered. 

Aerospace Technician and Mechanic Aptitude Virtual Job Tryout: To be considered for this position you will be required to complete a technical assessment as part of the selection process.  Failure to complete the assessment will remove you from consideration. 

Basic Qualifications (Required Skills/Experience):  

• 1+ years of structural experience in aerospace, automotive, maritime, construction or similar industry; this can include education and military.

• 1+ years experience following oral and written instructions in the form of blueprints, drawings, work instructions.

• 1+ years of experience using high impact vibratory tools; such as bucking/riveting. 

• Ability to stand 6-8 hours per day; walk constantly; climb or work from stairs/steps/ladders; bend and twist frequently; squat and kneel; wear hearing protection (ear inserts, canal caps, earmuffs); eye protection, and use hazardous chemicals.

• Ability to lift up to 35lbs.

• Ability to work in Confined Spaces (work within or pass through). Entry diameter 9.5”X17.7”.

• Proficiency in reading, writing, and speaking English.

Preferred Qualifications:  

• 1+ years of experience performing aircraft structural work or equivalate.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program.

Typical Education & Experience:  

High school graduate or GED preferred. 

Relocation: 

This position offers relocation based on candidate eligibility. 

Drug Free Workplace: 

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies. 

Union Representation Statement:  

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement. 

Shift:  

This position is for a variety of shifts.  

Total Rewards & Pay Transparency: 

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent.  Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.    

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.    

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.  

Pay is based upon candidate experience and qualifications, as well as market and business considerations.    

Pay: $26.32/hour, with potential to earn up to $56.36/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Apr. 10, 2026

Language Requirements

English Preferred

Relocation

This position offers relocation based on candidate eligibility.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Integral Fuel Cell Assembly (In- Tank Mechanic) to join our Join and Installation team in Everett and Renton, Washington. 

As an Integral Fuel Cell Assembly (In-Tank Mechanic), you will play a vital role in ensuring the highest standards of quality and safety while working within the confined spaces of aircraft fuel tanks. This position requires assembling and installing structural components, systems, and sub-assemblies to meet stringent quality requirements. You will be responsible for verifying kitted parts, performing drilling, riveting, and bonding, as well as assembling plumbing and electrical systems within the tank. Your attention to detail will be crucial as you conduct continuity checks, perform necessary rework, and ensure that all installations comply with specifications. Please note that this role involves working in tight spaces, including entering the wing through a approximately 9.5" x 17.7" opening; therefore, comfort with confined spaces is essential for success in this position.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation. 

Position Responsibilities : 

• Assemble and install parts, structural components, systems, and sub-assemblies to meet quality requirements for wing and horizontal stabilizer assemblies. 

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings. 

• Locate work areas using drawings, installation plans, or other paperwork that specifies airplane and section numbers. 

• Obtain and verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects. 

• Retrieve parts from the Parts Control Area or other designated locations if they are not pre-picked, ensuring they meet specifications. 

• Obtain a two-way radio and confined space flag before working in confined spaces, adhering to Communications System for Confined Hazardous Areas (CSCHA) rules and regulations. 

• Perform drilling, reaming, riveting, cold working, bonding, grounding, and sealing as necessary to complete work assignments. 

• Assemble and install aircraft plumbing and electrical systems within closed areas of the wing and horizontal stabilizer, ensuring compliance with specifications. 

• Perform pickup and rework, incorporating changes and conducting functional checks on work typically installed by lower classifications. 

• Perform continuity checks for electrical systems and hand form electrical wiring and soldering as necessary for work assignments.

• Perform final cleaning and closing of fuel cells, including vacuuming and installing fuel cell doors. 

• Locate and pre-install routing and clamping hardware for in-wing fuel tank electrical and plumbing systems as required. 

• Use precision measuring instruments to verify that quality standards are achieved. 

• Report job handicaps, such as errors in sequencing, parts, materials, and assembly procedures, following shop procedures. 

• Check work after completion of each operation to ensure assembly is complete and free of defects and remove and replace installations and related components as necessary. 

Physical Demands and Potential Hazards:  

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs. 

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting. 

• Work in environments that may involve contact with metals, solvents, and coolants. 

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards. 

• Adapt to varying noise levels and atmospheric conditions. 

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.  

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required . “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee  

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.  

Aerospace Technician and Mechanic Aptitude Virtual Job Tryout: To be considered for this position you will be required to complete a technical assessment as part of the selection process. Failure to complete the assessment will remove you from consideration. 

Basic Qualifications (Required Skills/Experience):  

• 1+ years of structural experience in aerospace, automotive, maritime, construction or similar industry; this can include education and military.

• 1+ years experience following oral and written instructions in the form of blueprints, drawings, work instructions.

• 1+ years of experience using high impact vibratory tools; such as bucking/riveting. 

• Ability to stand 6-8 hours per day; walk constantly; climb or work from stairs/steps/ladders; bend and twist frequently; squat and kneel; wear hearing protection (ear inserts, canal caps, earmuffs); eye protection, and use hazardous chemicals.

• Ability to lift up to 35lbs.

• Ability to work in Confined Spaces (work within or pass through). Entry diameter 9.5”X17.7”.

• Proficiency in reading, writing, and speaking English.

Preferred Qualifications :   

• 1+ years of experience performing aircraft structural work or equivalate.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program.

Typical Education & Experience:   

High school graduate or GED preferred.  

Relocation:  

This position offers relocation based on candidate eligibility.  

Drug Free Workplace :  

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.  

Union Representation Statement:   

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.  

Shift :  

This position is for a variety of shifts.  

Total Rewards & Pay Transparency:  

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent . Elements of the Total Rewards package include competitive base pay and variable compensation opportunities .   

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work .   

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.  

Pay is based upon candidate experience and qualifications, as well as market and business considerations .   

Pay: $26.32/hour, with potential to earn up to $56.36/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Apr. 10, 2026

Language Requirements

English Preferred

Relocation

This position offers relocation based on candidate eligibility.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Integral Fuel Cell Assembly (In- Tank Mechanic) to join our Join and Installation team in Everett and Renton, Washington. 

As an Integral Fuel Cell Assembly (In-Tank Mechanic), you will play a vital role in ensuring the highest standards of quality and safety while working within the confined spaces of aircraft fuel tanks. This position requires assembling and installing structural components, systems, and sub-assemblies to meet stringent quality requirements. You will be responsible for verifying kitted parts, performing drilling, riveting, and bonding, as well as assembling plumbing and electrical systems within the tank. Your attention to detail will be crucial as you conduct continuity checks, perform necessary rework, and ensure that all installations comply with specifications. Please note that this role involves working in tight spaces, including entering the wing through a approximately 9.5" x 17.7" opening; therefore, comfort with confined spaces is essential for success in this position.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation. 

Position Responsibilities : 

• Assemble and install parts, structural components, systems, and sub-assemblies to meet quality requirements for wing and horizontal stabilizer assemblies. 

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings. 

• Locate work areas using drawings, installation plans, or other paperwork that specifies airplane and section numbers. 

• Obtain and verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects. 

• Retrieve parts from the Parts Control Area or other designated locations if they are not pre-picked, ensuring they meet specifications. 

• Obtain a two-way radio and confined space flag before working in confined spaces, adhering to Communications System for Confined Hazardous Areas (CSCHA) rules and regulations. 

• Perform drilling, reaming, riveting, cold working, bonding, grounding, and sealing as necessary to complete work assignments. 

• Assemble and install aircraft plumbing and electrical systems within closed areas of the wing and horizontal stabilizer, ensuring compliance with specifications. 

• Perform pickup and rework, incorporating changes and conducting functional checks on work typically installed by lower classifications. 

• Perform continuity checks for electrical systems and hand form electrical wiring and soldering as necessary for work assignments.

• Perform final cleaning and closing of fuel cells, including vacuuming and installing fuel cell doors. 

• Locate and pre-install routing and clamping hardware for in-wing fuel tank electrical and plumbing systems as required. 

• Use precision measuring instruments to verify that quality standards are achieved. 

• Report job handicaps, such as errors in sequencing, parts, materials, and assembly procedures, following shop procedures. 

• Check work after completion of each operation to ensure assembly is complete and free of defects and remove and replace installations and related components as necessary. 

Physical Demands and Potential Hazards:  

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs. 

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting. 

• Work in environments that may involve contact with metals, solvents, and coolants. 

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards. 

• Adapt to varying noise levels and atmospheric conditions. 

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.  

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required . “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee  

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.  

Aerospace Technician and Mechanic Aptitude Virtual Job Tryout: To be considered for this position you will be required to complete a technical assessment as part of the selection process. Failure to complete the assessment will remove you from consideration. 

Basic Qualifications (Required Skills/Experience):  

• 1+ years of structural experience in aerospace, automotive, maritime, construction or similar industry; this can include education and military.

• 1+ years experience following oral and written instructions in the form of blueprints, drawings, work instructions.

• 1+ years of experience using high impact vibratory tools; such as bucking/riveting. 

• Ability to stand 6-8 hours per day; walk constantly; climb or work from stairs/steps/ladders; bend and twist frequently; squat and kneel; wear hearing protection (ear inserts, canal caps, earmuffs); eye protection, and use hazardous chemicals.

• Ability to lift up to 35lbs.

• Ability to work in Confined Spaces (work within or pass through). Entry diameter 9.5”X17.7”.

• Proficiency in reading, writing, and speaking English.

Preferred Qualifications :   

• 1+ years of experience performing aircraft structural work or equivalate.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program.

Typical Education & Experience:   

High school graduate or GED preferred.  

Relocation:  

This position offers relocation based on candidate eligibility.  

Drug Free Workplace :  

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.  

Union Representation Statement:   

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.  

Shift :  

This position is for a variety of shifts.  

Total Rewards & Pay Transparency:  

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent . Elements of the Total Rewards package include competitive base pay and variable compensation opportunities .   

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work .   

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.  

Pay is based upon candidate experience and qualifications, as well as market and business considerations .   

Pay: $26.32/hour, with potential to earn up to $56.36/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Apr. 10, 2026

Language Requirements

English Preferred

Relocation

This position offers relocation based on candidate eligibility.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airlines is excited to offer opportunities for an Inspector Electrical & Electronic Sub Assembly to join our Quality team in Everett and Renton, Washington.

As an Inspector for Electrical & Electronic Sub Assembly, you will be an integral part of our commitment to delivering top-notch quality in aerospace manufacturing. This exciting role places you at the intersection of technology and precision, where your keen eye for detail will ensure that every component meets the highest standards of safety and performance. You will engage with advanced inspection techniques and collaborate with a talented team to identify and resolve potential issues before they impact production. Please note that certification for visual acuity and color perception may be required for this position.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Communicate with shop personnel or check the Call Sheet for the next job or in-process inspection, obtaining applicable drawings and specifications.

• Ensure that the correct revisions of drawings and documents are being used, verifying that all paperwork and online systems are complete and accurate.

• Perform inspections and in-process inspections as required, including crimping, splicing, torque, bond, and ground checks.

• Conduct various tests and measurements, such as resistance tests, to ensure that wires meet specification requirements.

• Monitor manufacturing processes and document findings as required to ensure compliance with quality standards.

• Inspect electrical wire bundles and assemblies, ensuring all parts have been assembled according to drawings and specifications.

• Screen paperwork for options, substitutions, and effectiveness of parts and materials.

• Identify, investigate, and document discrepancies, reporting them to the shop as necessary.

• Reject wire bundles, assemblies, or installations as required, documenting discrepancies and processing Quality Assurance records.

• Indicate Quality Assurance acceptance on appropriate paperwork and online systems, processing documentation as required.

• Coordinate and complete travelers, investigating and clearing check orders as necessary.

• Initiate Inspection Record Change Requests (IRCR) and/or Shipside Action Trackers (SAT) as needed.

• Ensure that certifications for tools, test equipment, and personnel are current and compliant.

• Assist other employees by providing information and answering questions regarding functions, methods, and procedures.

• Perform first article inspections and FAA conformities, coordinating results as required.

• Enter data into various computing software systems, such as Common Manufacturing Execution System (CMES) and Enterprise Process Evaluation Systems (EPES).

• Collaborate with Engineering, Quality, and Manufacturing to evaluate and improve build processes and defect reduction initiatives.

• Initiate and document any nonconforming materials or assemblies according to specifications and procedures.

• Perform audits and surveillance of manufacturing and quality assurance processes to ensure compliance with standards.

• Witness or perform electrical continuity, voltage, resistance, capacitance, and bond or ground testing as required.

• Calibrate and certify electrical process tools, such as loggers, strippers, and crimpers.

• Refer to rejection tags and trouble reports to identify problems and initiate corrective actions.

Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications:

• 2+ years of experience as a Quality Inspector

• 1+ years of experience using precision measuring tools and equipment such as micrometers, calipers, and/or dial indicators

• 1+ years of experience reading and interpreting engineering drawings and specifications (e.g., blueprint/schematic reading, specification, change, design)

• Experience working with Microsoft Office (Excel, Word, PowerPoint)

• Proficiency in reading, writing, and speaking English

Preferred Qualifications:

• Electrical experience

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement:

• This position is for a variety of shifts

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent.  Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.  

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.  

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay: $26.32/hour, with potential to earn up to $56.36/hour in accordance with the terms of the relevant collective bargaining agreement

Applications for this position will be accepted until Apr. 24, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for a Painter Spray A -Major Assemblies to join our Joint and Installation team in Everett and Renton, Washington.

As a Painter Spray A - Major Assemblies, you will be essential in ensuring the highest standards of quality and safety in the painting process for our aircraft. Your role will involve collaborating with team members to complete painting assignments while meticulously preparing surfaces to guarantee proper adhesion and finish. You will utilize various paint materials and techniques, including both spray and brush methods, to achieve flawless results that meet inspection requirements. Your attention to detail will be critical as you clean and service equipment, mask areas for painting, and coordinate with safety and environmental teams to ensure a compliant work environment. Additionally, you will operate automated spray equipment and curing ovens, monitoring conditions to maintain optimal performance throughout the painting process.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Collaborate with employees of varying classifications to ensure the completion of painting assignments for aircraft, missiles, or space vehicles.

• Perform touch-up and pickup painting using both spray and brush techniques, adhering to inspection requirements.

• Prepare surfaces to ensure proper adhesion, including corrosion removal and paint stripping as needed.

• Prepare various paint materials, such as primers, enamels, and lacquers, according to specifications.

• Clean and service spray guns, paint tanks, brushes, hoses, and related equipment after use.

• Mask and unmask areas to facilitate corrosion removal or painting operations.

• Set up all necessary equipment and supplies for painting operations, including fall protection and protective equipment.

• Coordinate with safety, environmental, and fire organizations to ensure the shop is prepared for painting operations.

• Operate automated spray equipment, such as robots, for preparation and painting tasks.

• Operate curing ovens and monitor related equipment to ensure compliance with specifications, including temperature and humidity.

• Monitor and maintain time-sensitive materials and processes throughout the painting operation.

• Support customer inspections as required and screen work instructions to ensure proper workflow.

• Apply decals, part markings, and wrap finished parts or assemblies as required.

• Recognize and report any discrepancies or malfunctions in equipment or processes per established procedures.

• Obtain and maintain necessary certifications and qualifications for the role, and perform established autonomous maintenance as needed.

Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee

Resumes of current Puget Sound Boeing employees submitted via “Find Jobs” in Boeing/Workday will be considered as this job is not installed in QTTP (Quality Through Training Program).

Aerospace Technician and Mechanic Aptitude Virtual Job Tryout: To be considered for this position you will be required to complete a technical assessment as part of the selection process. Failure to complete the assessment will remove you from consideration.

Basic Qualifications:

• 1+ years of experience in prepping, cleaning, and painting various surfaces in industrial, commercial, or academic settings.

• 1+ years of experience using various types of paint equipment and applicators, such as HVLP, pneumatic, electrostatic, and others.

• 1+ years of experience mixing paints.

• 1+ years experience utilizing and following detailed work instructions, reading and interpreting blueprints, drawings, and specifications.

• 1+ years of experience handling chemicals and/or hazardous materials

• Experience working from heights & using fall protection equipment with weight limitations.

Preferred Qualifications:

• 1+ year of experience performing aircraft or autobody painting and finishing operations.

• Completed 1+ year of autobody paint/collision repair in high school or community and technology college academic program.

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• This position offers relocation based on candidate eligibility.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement:

• This position is for a variety of shifts

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent. Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay is based upon candidate experience and qualifications, as well as market and business considerations.

Summary pay range: $25.32/hour, with potential to earn up to $54.76/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Mar. 31, 2026

Language Requirements

English Preferred

Relocation

This position offers relocation based on candidate eligibility.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airlines is excited to offer opportunities for a Sealer Aircraft Integral Fuel Tank Components to join our Joint and Installation team in Everett and Renton , Washington .

As a Sealer for Aircraft Integral Fuel Tank Components, you will play a vital role in ensuring the highest standards of quality and safety in the sealing and assembly processes. Your responsibilities will include working from blueprints and specifications to clean surfaces, apply sealants, and prepare fuel vents for leak tests. You will also perform necessary rework and apply corrosion preventative seals to maintain the integrity of fuel tank components. Attention to detail is essential as you assist with pressure testing operations and coordinate effectively with supervisors and team members to ensure seamless communication across shifts.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Work from blueprints, documents, standards, and other required specifications to complete assigned tasks.
• Obtain daily work assignments from the team leader or supervisor and read Installation Plans and applicable drawings to determine work areas.
• Select appropriate cleaning solvents and clean interior and exterior surfaces prior to sealing.
• Load sealing guns and clean sealing equipment, ensuring proper functionality.
• Hand mix sealant as required and perform rework or pickups on assigned assemblies.
• Assist with pressure testing operations as assigned.
• Use specified agents and procedures for tasks such as removing protective coatings, applying corrosion inhibitors, and reactivating paint surfaces.
• Ensure proper grounding of the aircraft prior to cleaning operations and set up ventilation equipment to supply fresh air in work areas.
• Keep supervisors informed of progress and coordinate information with employees on other shifts.
• Mask areas as required to facilitate corrosion removal or painting operations.
• Prepare fuel vents for leak tests and restore them to normal after testing.
• Apply corrosion preventative seal as required and measure, layout, and apply aerodynamic seals to skin gaps on leading and trailing edge panels.
• Submit completed jobs or in-process checks to inspectors for acceptance or rejection.
• Apply decals, metalcals, placards, and charts to specific locations on parts and assemblies as required.

Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.
• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.
• Work in environments that may involve contact with metals, solvents, and coolants.
• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.
• Adapt to varying noise levels and atmospheric conditions.
• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications :

• 1+ years of experience with paints, coatings, finishes, and/or sealants.

• Experience in handling chemicals and/or hazardous materials.

• Experience in prepping, cleaning, and painting various surfaces in industrial, commercial, or academic settings.

• Experience working from heights & using fall protection equipment with weight limitations.

• Experience with safety process and/or procedures in a manufacturing or operations environment.

• Experience working with tools and following work instructions.

Preferred Qualifications:

• 1+ year of experience performing aerospace sealing.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program.

• Completed 1+ year of aerospace sealing in high school or community and technology college academic program.

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement :

• This position is for a variety of shifts

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent. Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay: $25.00/hour, with potential to earn up to $51.82/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Aug. 28, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Assembler Power Plant B to become part of our Join and Installation team in Everett and Kent, Washington.

Join our dynamic team as an Assembler Power Plant B, where your skills will be pivotal in constructing and assembling critical aircraft components. In this essential role, you will utilize production drawings and specifications to accurately install, fit, and align parts for power packs and strut assemblies. Your attention to detail will ensure that each component is meticulously drilled, reamed, and riveted, while your expertise in pre-assembly will streamline the process for wiring harnesses and tubing assemblies. You will operate advanced material handling equipment to efficiently load and unload engines and struts. Your ability to verify dimensions and check for defects will be crucial in maintaining our commitment to excellence. If you are passionate about aviation and thrive in a collaborative environment, we invite you to contribute to our mission of delivering high-quality aircraft systems.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Install, fit, fasten, align, adjust, and connect parts and assemblies to build aircraft power packs and strut assemblies.

• Use production drawings, specifications, and assembly pages to derive measurements and locate points for part marking and layout preparation.

• Perform drilling, reaming, riveting, and soldering necessary for assembly tasks.

• Review work orders and installation plans to determine job priorities and obtain appropriate drawings and production illustrations.

• Obtain and verify kitted detail parts and assemblies, ensuring they are correct and free of defects.

• Pre-assemble components such as wiring harnesses and tubing assemblies using power and hand tools.

• Operate material handling equipment, including overhead cranes and scissor lifts, to load and unload engines and struts.

• Align parts and assemblies to mating surfaces, temporarily securing them in place and checking for proper alignment.

• Attach, seal, and connect parts, assemblies, and wires using the correct fasteners and tools, tightening per specifications.

• Torque fasteners and install safety devices such as lock wires and cotter pins as required by drawings or specifications.

• Seal hydraulic fittings and access doors, applying necessary fluids, primers, and adhesives according to specifications.

• Operate various tools, including pull rivet guns and countersinks, to fasten and torque parts and assemblies.

• Verify close tolerance dimensions using precision measuring tools and check work for defects before inspection.

• Maintain personal and tool certifications, ensuring compliance with safety and operational standards.

• Communicate with team leaders and supervisors regarding job progress, issues, and assistance needed, while consulting with engineering and planning as required.

Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs. to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

To meet U.S. export control compliance requirements, a “U.S. Person” as defined by 22 C.F.R. §120.62 is required. “U.S. Person” includes U.S. Citizen, U.S. National, lawful permanent resident, refugee, or asylee. Do you meet this requirement?

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications:

• 1+ years of experience working with mechanical or structures related statements of work; such as construction, aerospace, automotive, maritime or similar industry; this can include education and military.

• 1+ year experience utilizing and following detailed work instructions, reading and interpreting blueprints, drawings, and specifications.

• Ability to walk constantly throughout the workday; stand 6-8 hours per day; climb or work from stairs/steps up to 8 hours per day; climb ladders; bend and twist frequently up to six hours per day; squat and kneel.

• Ability to lift up to 35 pounds.

• This position requires you to wear eye, hearing, foot, hand, respirator and other personal protective equipment/safety gear at all times.

• Proficiency in reading, writing, and speaking English

Preferred Qualifications:

• 1+ years of experience performing aircraft structural work or equivalate.

• 1+ years of experience using high impact vibratory tools; such as bucking/riveting.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program

Conflict of Interest: 

• Successful candidates for this position must successfully complete the Company’s Conflict of Interest (COI) assessment process.

Typical Education & Experience:

• High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace

• Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

• This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Safety Sensitive Statement:

• This is a safety-sensitive position and is subject to Department of Transportation (DOT) random drug and alcohol testing.

Shift Work Statement:

• This position is for a variety of shifts

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent.  Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.  

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.  

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay: $25.00/hour, with potential to earn up to $55.30/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Sept. 04, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Structural Mechanic IV in GAC Brunswick

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Blueprint reading, process code and fabrication experience, airframe structures and repair work required.

1. Use ability as a skilled specialist to contribute to the development of employees and techniques and completes work in innovative and effective ways .
2. Perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements .
3. Use complicated schematics/blueprints, engineering drawings and technical instructions to safely perform layout, fabrication, and installation of parts, equipment or fabricated items on aircraft. Coordinate with supervision and Inspection to ensure compliance with internal and FAA paperwork, sign-offs and quality specifications .
4. Ability to move to new tasks with minimal, short-term impact to established goal hours and schedule .
5. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structures .
6. Read work orders, blueprints, lofts, sketches, and operation sheets to determine sequence of operations, type size for rivets, hole pattern for rivets, cutand form plastics and follow standard operating procedures when using adhesives, sealants and solvents .
7. Check all work and ensure a defect free assembly prior to final inspection .
8. Mentor, train, and assist other team members in interpretation of blueprints, drawings, and engineering orders; develop methods and shop aids to resolve production installation difficulties and problems .
9. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
10. Align and assembles parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners .
11. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
12. Plan and organize workloads and resource requirements to meet or exceed goal hours and schedule expectations. Assist in overseeing projects or other technicians and assesses requirements of assigned tasks to procure required. materials and documentation for assigned tasks .
13. Maintain a neat and orderly work area, supports the company 5S, Lean Initiative Program, and complies with all safety regulations .
14. Support Lean Activities, comply with all safety, 5S, and housekeeping policies.

1. Good working knowledge of computers and related software.
2. Must be able to read and interpret blue prints.
3. Must be skilled in close tolerance work and have knowledge of use of special tools and equipment. Should be able to use all tools required. to do the job.
4. Must be able to use mathematical formulas by solving dimensional problems using fractions, decimal fractions and whole numbers.
5. Thorough knowledge in the use of multiple measuring devices, demonstrated ability to use within specified tolerance.
6. Must be able to work any shift.
7. Must be able to lift 50 lbs.
8. Must be able to climb ladders, stands, stairs and work in small spaces and/or restricted areas.
9. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 231359

Category: Operations

Percentage of Travel: Up to 25%

Shift: Multiple Shifts

Employment Type: Full-time

Posting End Date: 03/23/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

SkillBridge Structural Mechanic in N/A

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Must be eligible for the DOD SkillBridge Program.

You may be eligible to participate in SkillBridge if you: Have 180 days of service or fewer remaining prior to your date of discharge and you have at least 180 continuous days of active Military service. Obtain approval from your unit commander. Agree that participation in the DOD SkillBridge can be terminated at any time by the service if mission requirements dictate.

Education and Experience Requirements

SkillBridge Structural Mech II- 2 years related structural assembly experience.

SkillBridge Structural Mech III- 4 years related structural assembly experience.

SkillBridge Structural Mech IV - 6 years related structural assembly experience.

1. Safely perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements. Safely perform sheetmetal layout, fabrication, and installation of parts, equipment or fabricated items on aircraft .
2. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structure .
3. Read work orders, blueprints, lofts, sketches and operation sheets to determine sequence of operations, type size and hole pattern for rivets, cut and form plastics and follow standard operating procedures when using adhesives, sealants, and solvents .
4. Check all work and ensure a defective free assembly prior to final inspection .
5. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
6. Align and assemble parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners. Utilizing proper tooling, shape and form complex angles and configurations according to blueprint specifications or written/verbal information .
7. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
8. Maintain a neat and orderly work area, supports the company 5S Program, and complies with all safety regulations. Use personal protective equipment as required.

1. Properly collect and dispose of waste fuel, oil, hydraulic fluids, de-icing fluids, and solvent rags .
2. Ensure accurate daily job charging to the aircraft .
3. Exchange job related information and coordinate work activities between shifts through turn over report meetings and direct contact with leadership .
4. Assist in maintaining shop equipment and associated JSAs .
5. Support Lean Activities .

1. Must be able to read and interpret blue prints.
2. Basic computer skills and basic shop math skills.
3. Must be able to read a scale and perform basic shop math.
4. Read and comprehend basic documents and instructions.
5. Must have essential personal skills, which include an aptitude for hands-on craftwork, a professional attitude, attention to detail, ability to work with people and to meet demanding schedules.
6. Must demonstrate good housekeeping and safety practices.
7. Ability to work with composite resins and materials.
8. Must be able to work any shift.
9. Must be able to climb ladders/stands/stairs and work in small spaces or restricted areas & lift 50 lbs.
10. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 230675

Category: Operations

Percentage of Travel: Up to 25%

Shift: Multiple Shifts

Employment Type: Skillbridge

Posting End Date: 09/27/2025

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Structural Mechanic 2 in GAC St. Louis

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Employee needs to be skilled in sheet metal structures and repairs.

The compensation range for this role is $26.51 - $30.93 per hour.

Final compensation for this role will be determined by several factors including but not limited to: minimum and preferred qualifications, knowledge, skills, abilities, education, experience, and location.

Gulfstream employees benefit from a total rewards package that includes competitive compensation, comprehensive benefits plans, wellness programs, paid leave and tuition assistance. Our U.S. benefits package includes:

• Medical, prescription, dental and vision coverage
• Life and disability insurance
• Retirement savings plan
• Employee assistance plan
• Voluntary programs such as adoption assistance, prepaid legal assistance, home and auto insurance, and accident insurance.

1. Safely perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements Safely perform sheetmetal layout, fabrication, and installation of parts, equipment or fabricated items on aircraft .
2. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structure .
3. Read work orders, blueprints, lofts, sketches and operation sheets to determine sequence of operations, type size and hole pattern for rivets, cut and form plastics and follow standard operating procedures when using adhesives, sealants, and solvents .
4. Check all work and ensure a defective free assembly prior to final inspection .
5. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
6. Align and assemble parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners. Utilizing proper tooling, shape and form complex angles and configurations according to blueprint specifications or written/verbal information .
7. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
8. Maintain a neat and orderly work area, supports the company 5S Program, and complies with all safety regulations. Use personal protective equipment as required.
9. Able to work with minimal supervision on duties and tasks .
10. Participate in continuous improvement activities (e.g. YIAW, Kaizen events, etc.) .
11. Properly use and maintain company-provided tools and equipment and returns items to tool room after use .
12. Ensure standard operating procedures are followed when operating ground support equipment .

1. Properly collect and dispose of waste fuel, oil, hydraulic fluids, de-icing fluids, and solvent rags .
2. Ensure accurate daily job charging to the aircraft .
3. Exchange job related information and coordinate work activities between shifts through turn over report meetings and direct contact with leadership .
4. Assist in maintaining shop equipment and associated JSAs .
5. Support Lean Activities .

1. Must be able to read and interpret blue prints.
2. Basic computer skills and basic shop math skills.
3. Must be able to read a scale and perform basic shop math.
4. Read and comprehend basic documents and instructions.
5. Must have essential personal skills, which include an aptitude for hands-on craftwork, a professional attitude, attention to detail, ability to work with people and to meet demanding schedules.
6. Must demonstrate good housekeeping and safety practices.
7. Ability to work with composite resins and materials.
8. Must be able to work any shift.
9. Must be able to climb ladders/stands/stairs and work in small spaces or restricted areas & lift 50 lbs.
10. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 231417

Category: Operations

Percentage of Travel: Up to 25%

Shift: First

Employment Type: Full-time

Posting End Date: 04/03/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Structural Mechanic 4 in GAC Van Nuys

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Most be able to work any shift.

Most have an extensive knowledge of sheetmetal and structural repairs.

The compensation range for this role is $34.15 - $39.84 per hour.

Final compensation for this role will be determined by several factors including but not limited to: minimum and preferred qualifications, knowledge, skills, abilities, education, experience, and location.

Gulfstream employees benefit from a total rewards package that includes competitive compensation, comprehensive benefits plans, wellness programs, paid leave and tuition assistance. Our U.S. benefits package includes:

• Medical, prescription, dental and vision coverage
• Life and disability insurance
• Retirement savings plan
• Employee assistance plan
• Voluntary programs such as adoption assistance, prepaid legal assistance, home and auto insurance, and accident insurance.

1. Use ability as a skilled specialist to contribute to the development of employees and techniques and completes work in innovative and effective ways .
2. Perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements .
3. Use complicated schematics/blueprints, engineering drawings and technical instructions to safely perform layout, fabrication, and installation of parts, equipment or fabricated items on aircraft. Coordinate with supervision and Inspection to ensure compliance with internal and FAA paperwork, sign-offs and quality specifications .
4. Ability to move to new tasks with minimal, short-term impact to established goal hours and schedule .
5. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structures .
6. Read work orders, blueprints, lofts, sketches, and operation sheets to determine sequence of operations, type size for rivets, hole pattern for rivets, cutand form plastics and follow standard operating procedures when using adhesives, sealants and solvents .
7. Check all work and ensure a defect free assembly prior to final inspection .
8. Mentor, train, and assist other team members in interpretation of blueprints, drawings, and engineering orders; develop methods and shop aids to resolve production installation difficulties and problems .
9. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
10. Align and assembles parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners .
11. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
12. Plan and organize workloads and resource requirements to meet or exceed goal hours and schedule expectations. Assist in overseeing projects or other technicians and assesses requirements of assigned tasks to procure required. materials and documentation for assigned tasks .
13. Maintain a neat and orderly work area, supports the company 5S, Lean Initiative Program, and complies with all safety regulations .
14. Support Lean Activities, comply with all safety, 5S, and housekeeping policies.

1. Good working knowledge of computers and related software.
2. Must be able to read and interpret blue prints.
3. Must be skilled in close tolerance work and have knowledge of use of special tools and equipment. Should be able to use all tools required. to do the job.
4. Must be able to use mathematical formulas by solving dimensional problems using fractions, decimal fractions and whole numbers.
5. Thorough knowledge in the use of multiple measuring devices, demonstrated ability to use within specified tolerance.
6. Must be able to work any shift.
7. Must be able to lift 50 lbs.
8. Must be able to climb ladders, stands, stairs and work in small spaces and/or restricted areas.
9. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 230658

Category: Operations

Percentage of Travel: Up to 25%

Shift: First

Employment Type: Full-time

Posting End Date: 03/27/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Structural Mechanic 4 (Weekend Day Shift) in GAC St. Louis

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Candidate must be well trained on using sheet metal structures tooling, understand and interpret structural drawings, and have experience on aircraft structural repairs. This shift is primarily a Weekend Day Shift (Friday-Sunday from 6:00am to 6:30pm), but candidate must be willing to work multiple shifts as required.

The base compensation range for this role is $31.19 - $36.38 per hour.

Final compensation for this role will be determined by several factors including but not limited to: minimum and preferred qualifications, knowledge, skills, abilities, education, experience, and location.

Gulfstream employees benefit from a total rewards package that includes competitive compensation, comprehensive benefits plans, wellness programs, paid leave and tuition assistance. Our U.S. benefits package includes:

• Medical, prescription, dental and vision coverage
• Life and disability insurance
• Retirement savings plan
• Employee assistance plan
• Voluntary programs such as adoption assistance, prepaid legal assistance, home and auto insurance, and accident insurance.

1. Use ability as a skilled specialist to contribute to the development of employees and techniques and completes work in innovative and effective ways .
2. Perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements .
3. Use complicated schematics/blueprints, engineering drawings and technical instructions to safely perform layout, fabrication, and installation of parts, equipment or fabricated items on aircraft. Coordinate with supervision and Inspection to ensure compliance with internal and FAA paperwork, sign-offs and quality specifications .
4. Ability to move to new tasks with minimal, short-term impact to established goal hours and schedule .
5. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structures .
6. Read work orders, blueprints, lofts, sketches, and operation sheets to determine sequence of operations, type size for rivets, hole pattern for rivets, cutand form plastics and follow standard operating procedures when using adhesives, sealants and solvents .
7. Check all work and ensure a defect free assembly prior to final inspection .
8. Mentor, train, and assist other team members in interpretation of blueprints, drawings, and engineering orders; develop methods and shop aids to resolve production installation difficulties and problems .
9. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
10. Align and assembles parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners .
11. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
12. Plan and organize workloads and resource requirements to meet or exceed goal hours and schedule expectations. Assist in overseeing projects or other technicians and assesses requirements of assigned tasks to procure required. materials and documentation for assigned tasks .
13. Maintain a neat and orderly work area, supports the company 5S, Lean Initiative Program, and complies with all safety regulations .
14. Support Lean Activities, comply with all safety, 5S, and housekeeping policies.

1. Good working knowledge of computers and related software.
2. Must be able to read and interpret blue prints.
3. Must be skilled in close tolerance work and have knowledge of use of special tools and equipment. Should be able to use all tools required. to do the job.
4. Must be able to use mathematical formulas by solving dimensional problems using fractions, decimal fractions and whole numbers.
5. Thorough knowledge in the use of multiple measuring devices, demonstrated ability to use within specified tolerance.
6. Must be able to work any shift.
7. Must be able to lift 50 lbs.
8. Must be able to climb ladders, stands, stairs and work in small spaces and/or restricted areas.
9. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 229842

Category: Operations

Percentage of Travel: Up to 25%

Shift: Weekend Days

Employment Type: Full-time

Posting End Date: 03/18/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Electrical Systems- Assembler Installer to join our Joint and Installation team in Everett and Renton, Washington.

We are seeking a skilled Aircraft Electrical Systems Installer to join our dynamic team. In this role, you will be responsible for assembling and installing aircraft electrical systems, equipment, and accessories to meet stringent quality requirements. Your expertise will ensure that all electrical components are accurately located and installed, contributing to the overall safety and performance of our aircraft.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities

• Assemble and install aircraft electrical systems, equipment, and accessories in the airplane and/or specific sections, adhering to quality requirements.

• Locate points, parts, holes, wire bundles, assemblies, etc., using previously established, marked, or generally known station lines or index points, deriving measurements and related information from electrical specifications and authorized sources.

• Conduct continuity checks to ensure proper functionality of electrical systems.

• Utilize prints, changes, schematic drawings, documents, position boards, assembly pages, photographs, makeup charts, work orders, and production illustrations to complete assigned tasks.

• Execute any necessary pickups, authorized changes, and rework independently or on comparable work, often without the use of wire forming boards, jigs, fixtures, or tooling. Typically assigned work that has been previously sequenced.

• Select appropriate parts, materials, tools, assemblies, and shields to effectively accomplish work assignments.

• Report job handicaps, such as errors in sequencing, parts, materials, wire sizes and types, and assembly procedures, in accordance with shop procedures outlined by the supervisor.

• Perform hand forming of electrical wiring and soldering as required to complete work assignments.

• Carry out mechanical work when it is similar in complexity and incidental but necessary for the efficient completion of work assignments.

• Execute necessary riveting tasks as part of the assembly process.

Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications

• 1+ years of experience in electrical assembly installation.

• 1+ years of experience with safety process and/or procedures in a manufacturing or operations environment (LOTO).

• 1+ years of experience handling chemicals and/or hazardous materials.

• Ability to recognize colors.

• Ability to work in confined spaces.

• Ability to support frequent standing, walking, lifting, and working at heights with or without equipment assistance.

• Proficiency in reading, writing, and speaking English.

Preferred Qualifications:

• 1+ years of experience as an Electrician or Apprentice.

• Completion of an electrical trade school program or have military related electrical experience.

• Enrolled in a Boeing partnered manufacturing related high school or community and technology college academic program.

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement:

• This position is for a variety of shifts

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent.  Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.  

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.  

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay: $24.32/hour, with potential to earn up to $53.30/hour in accordance with the terms of the relevant collective bargaining agreement.

Applications for this position will be accepted until Jul. 09, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Structural Mechanic III - Sign On Bonus Available in GAC Mesa

Unique Skills:

At Gulfstream, our people are at the heart of everything we do. We believe in inspiring and empowering every individual to reach their fullest potential. From workforce development and meaningful connections to a culture of trust, respect, and integrity, we invest in our employees so they can do their best work and achieve success together. Creating and delivering the world's finest aviation experience starts with our people and when our people thrive, so does our mission.

Heavy structures MOD experience preferred.

1. Safely perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements. Safely perform sheetmetal layout, fabrication, and installation of parts, equipment or fabricated items on aircraft .
2. Possess the proven ability to move to new tasks with only a moderate, short-term impact to established goal hours and schedule .
3. Rivet structural members, assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Ability to remove fasteners without damaging structures .
4. Read work orders, blueprints, lofts, sketches, and operation sheets to determine sequence of operations, type size and hole pattern for rivets, cut and form plastics and follow standard operating procedures when using adhesives, sealants, and solvents .
5. Check all work and ensure a defective free assembly prior to final inspection .
6. Instruct and assist other team members in interpretation of blueprints, drawings, and engineering orders; develop methods and shop aids to resolve production installation difficulties and problems .
7. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
8. Align and assemble parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners. Utilizing proper tooling, shape and form complex angles and configurations according to blueprint specifications or written/verbal information .
9. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
10. Maintain a neat and orderly work area, supports the company 5S & Lean Initiative Program and complies with all safety regulations. Use of personal protective equipment as required.

1. Participate in continuous improvement activities .
2. Properly use and maintain company-provided tools and equipment and returns items to tool room after use .
3. Ensure standard operating procedures are followed when operating ground support equipment .
4. Properly collect and dispose of waste fuel, oil, hydraulic fluids, de-icing fluids, and solvent rags .
5. Ensure accurate daily job charging to the aircraft .
6. Exchange job related information and coordinate work activities between shifts through turn over report meetings and direct contact with leadership .

1. Basic computer and basic shop math skills.
2. Read and comprehend basic documents and instructions and read a scale.
3. Must have essential personal skills and possess aptitude for hands-on craftswork, a professional attitude, attention to detail, ability to work with people and to meet demanding schedules.
4. Must be skilled in close tolerance work and have knowledge of use of special tools and equipment.
5. Ability to work with composite resins and materials.
6. Must be able to work any shift.
7. Must be able to climb ladders, stands, stairs, and work in small spaces or restricted areas & lift 50 lbs.

Additional Information

Requisition Number: 230580

Category: Operations

Percentage of Travel: Up to 25%

Shift: Multiple Shifts

Employment Type: Full-time

Posting End Date: 04/30/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Structural Mechanic IV - Special Missions in GAC Brunswick

Unique Skills:

G550 preferred

1. Use ability as a skilled specialist to contribute to the development of employees and techniques and completes work in innovative and effective ways .
2. Perform assembly and fitting of detail parts and structures and varied drilling and riveting operations; ensures parts/assembly meet requirements .
3. Use complicated schematics/blueprints, engineering drawings and technical instructions to safely perform layout, fabrication, and installation of parts, equipment or fabricated items on aircraft. Coordinate with supervision and Inspection to ensure compliance with internal and FAA paperwork, sign-offs and quality specifications .
4. Ability to move to new tasks with minimal, short-term impact to established goal hours and schedule .
5. Rivet structural assemblies and parts using all tools required. to do the job (e.g. portable riveting guns, pneumatic drills, counter sinks, rivet shavers, files, reamers, rivets). Must display the ability to remove fasteners without damaging structures .
6. Read work orders, blueprints, lofts, sketches, and operation sheets to determine sequence of operations, type size for rivets, hole pattern for rivets, cutand form plastics and follow standard operating procedures when using adhesives, sealants and solvents .
7. Check all work and ensure a defect free assembly prior to final inspection .
8. Mentor, train, and assist other team members in interpretation of blueprints, drawings, and engineering orders; develop methods and shop aids to resolve production installation difficulties and problems .
9. Maintain and use all logs and records (e.g. MIR sheets, DMTs, Crabs, PCOs) .
10. Align and assembles parts to be riveted using jigs, holding fixtures, pins, clamps, and fasteners .
11. Make repairs per Discrepant Material Tags (DMT), Material Review Request (MRR), Production Change Orders (PCO), performs necessary rework to ensure installations meet conformity .
12. Plan and organize workloads and resource requirements to meet or exceed goal hours and schedule expectations. Assist in overseeing projects or other technicians and assesses requirements of assigned tasks to procure required. materials and documentation for assigned tasks .
13. Maintain a neat and orderly work area, supports the company 5S, Lean Initiative Program, and complies with all safety regulations .
14. Support Lean Activities, comply with all safety, 5S, and housekeeping policies.

1. Good working knowledge of computers and related software.
2. Must be able to read and interpret blue prints.
3. Must be skilled in close tolerance work and have knowledge of use of special tools and equipment. Should be able to use all tools required. to do the job.
4. Must be able to use mathematical formulas by solving dimensional problems using fractions, decimal fractions and whole numbers.
5. Thorough knowledge in the use of multiple measuring devices, demonstrated ability to use within specified tolerance.
6. Must be able to work any shift.
7. Must be able to lift 50 lbs.
8. Must be able to climb ladders, stands, stairs and work in small spaces and/or restricted areas.
9. Must be able to read, write, speak, and understand the English language.

Additional Information

Requisition Number: 231173

Category: Operations

Percentage of Travel: Up to 25%

Shift: Multiple Shifts

Employment Type: Full-time

Posting End Date: 04/10/2026

Equal Opportunity Employer / Individuals with Disabilities / Protected Veterans

Gulfstream does not provide work visa sponsorship for this position, unless the applicant is a currently sponsored Gulfstream employee.

Legal Information Site Utilities Contacts Sitemap
Copyright 2025 Gulfstream Aerospace Corporation. All Rights Reserved. A General Dynamics Company .

Gulfstream Aerospace Corporation, a wholly-owned subsidiary of General Dynamics (NYSE: GD), designs, develops, manufactures, markets, services and supports the world's most technologically-advanced business jet aircraft

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Assembler Installer Cable Controlled Systems to join our Joint and Installation team in Everett and Renton, Washington.

As an Assembler Installer for Cable Controlled Systems, you will be pivotal in ensuring the highest standards of quality and safety in the installation and assembly processes. Your expertise will be essential as you perform critical tasks such as reaming, riveting, and setting cable tensions using a tension meter, all while adhering to precise specifications. You will meticulously select and verify parts, ensuring they are free of defects and suitable for installation, while also utilizing blueprints and work orders to guide your work. Your attention to detail will be crucial as you clean surfaces, apply sealants, and conduct thorough inspections to confirm that all assemblies meet regulatory compliance and operational excellence.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Perform pickup, rework, authorized changes, and functional checks on work typically installed or assembled by lower classifications.

• Use a tension meter to set cable tension according to specifications.

• Conduct reaming and riveting as necessary to complete work assignments.

• Report job handicaps, such as errors in parts, materials, or assembly procedures, following shop procedures.

• Select appropriate parts, materials, and tools, and work with blueprints, assembly pages, and work orders to install and adjust cable-controlled systems in the aircraft.

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings.

• Locate work areas using drawings or paperwork that specify airplane and section numbers.

• Verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects.

• Obtain parts from the Parts Control Area if they are not pre-picked, ensuring they meet specifications.

• Drill, ream, and countersink holes in parts/assemblies per specifications, using appropriate tools.

• Disassemble parts and deburr holes to prepare for fastener installation.

• Use solvents to clean surfaces prior to sealing or assembly, and apply sealants, alodine, primers, adhesives, and special finishes as required.

• Install cable control pulleys and rig control cables according to drawings and specifications.

• Check and adjust actuator motors for full travel of flight control systems using power sources and hand tools.

• Clean the work area and ensure the removal of Foreign Object Debris (FOD) and submit completed jobs or in-process checks to inspectors as required.

• Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee.

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications:

• Experience using hand tools and/or hand-held power tools

• Experience working with safety and quality processes and procedures.

• Basic Computer experience and competency.

• Ability to walk constantly throughout the workday; stand 6-8 hours per day; climb or work from stairs/steps up to 8 hours per day; climb ladders; bend and twist frequently up to six hours per day; squat and kneel.

• Able to perform work at heights up to 50 feet above ground level with appropriate safety gear.

Preferred Qualifications:

• Experience reading and interpreting drawings, specifications,

• material processes, schematic and diagrams

• Attended a Boeing partnered manufacturing related high school or

• Preferred community and technology college academic program

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement:  

• This position is for a variety of shifts  

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent. Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay is based upon candidate experience and qualifications, as well as market and business considerations.

Summary pay range: $24.32 – $53.30

Applications for this position will be accepted until Sept. 04, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Assembler Installer Cable Controlled Systems to join our Joint and Installation team in Everett and Renton, Washington.

As an Assembler Installer for Cable Controlled Systems, you will be pivotal in ensuring the highest standards of quality and safety in the installation and assembly processes. Your expertise will be essential as you perform critical tasks such as reaming, riveting, and setting cable tensions using a tension meter, all while adhering to precise specifications. You will meticulously select and verify parts, ensuring they are free of defects and suitable for installation, while also utilizing blueprints and work orders to guide your work. Your attention to detail will be crucial as you clean surfaces, apply sealants, and conduct thorough inspections to confirm that all assemblies meet regulatory compliance and operational excellence.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Perform pickup, rework, authorized changes, and functional checks on work typically installed or assembled by lower classifications.

• Use a tension meter to set cable tension according to specifications.

• Conduct reaming and riveting as necessary to complete work assignments.

• Report job handicaps, such as errors in parts, materials, or assembly procedures, following shop procedures.

• Select appropriate parts, materials, and tools, and work with blueprints, assembly pages, and work orders to install and adjust cable-controlled systems in the aircraft.

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings.

• Locate work areas using drawings or paperwork that specify airplane and section numbers.

• Verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects.

• Obtain parts from the Parts Control Area if they are not pre-picked, ensuring they meet specifications.

• Drill, ream, and countersink holes in parts/assemblies per specifications, using appropriate tools.

• Disassemble parts and deburr holes to prepare for fastener installation.

• Use solvents to clean surfaces prior to sealing or assembly, and apply sealants, alodine, primers, adhesives, and special finishes as required.

• Install cable control pulleys and rig control cables according to drawings and specifications.

• Check and adjust actuator motors for full travel of flight control systems using power sources and hand tools.

• Clean the work area and ensure the removal of Foreign Object Debris (FOD) and submit completed jobs or in-process checks to inspectors as required.

• Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee.

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications:

• Experience using hand tools and/or hand-held power tools

• Experience working with safety and quality processes and procedures.

• Basic Computer experience and competency.

• Ability to walk constantly throughout the workday; stand 6-8 hours per day; climb or work from stairs/steps up to 8 hours per day; climb ladders; bend and twist frequently up to six hours per day; squat and kneel.

• A ble to perform work at heights up to 50 feet above ground level with appropriate safety gear.

Preferred Qualifications:

• Experience reading and interpreting drawings, specifications,

• material processes, schematic and diagrams

• Attended a Boeing partnered manufacturing related high school or

• Preferred community and technology college academic program

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement :  

• This position is for a variety of shifts   

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent. Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay is based upon candidate experience and qualifications, as well as market and business considerations.

Summary pay range: $24.32 – $53.30

Applications for this position will be accepted until Sept. 04, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

Job Description

At Boeing, we innovate and collaborate to make the world a better place. We’re committed to fostering an environment for every teammate that’s welcoming, respectful and inclusive, with great opportunity for professional growth. Find your future with us.

Boeing Commercial Airplanes is excited to offer opportunities for an Assembler Installer Cable Controlled Systems to join our Joint and Installation team in Everett and Renton, Washington.

As an Assembler Installer for Cable Controlled Systems, you will be pivotal in ensuring the highest standards of quality and safety in the installation and assembly processes. Your expertise will be essential as you perform critical tasks such as reaming, riveting, and setting cable tensions using a tension meter, all while adhering to precise specifications. You will meticulously select and verify parts, ensuring they are free of defects and suitable for installation, while also utilizing blueprints and work orders to guide your work. Your attention to detail will be crucial as you clean surfaces, apply sealants, and conduct thorough inspections to confirm that all assemblies meet regulatory compliance and operational excellence.

You will play a critical role in upholding our commitment to safety and quality standards, ensuring that all operations meet regulatory compliance and operational excellence. If you are detail-oriented, possess strong technical skills, and thrive in a collaborative environment, we invite you to apply and be a part of our mission to deliver excellence in aviation.

Position Responsibilities:

• Perform pickup, rework, authorized changes, and functional checks on work typically installed or assembled by lower classifications.

• Use a tension meter to set cable tension according to specifications.

• Conduct reaming and riveting as necessary to complete work assignments.

• Report job handicaps, such as errors in parts, materials, or assembly procedures, following shop procedures.

• Select appropriate parts, materials, and tools, and work with blueprints, assembly pages, and work orders to install and adjust cable-controlled systems in the aircraft.

• Review bar charts or automated timelines to determine job assignments and obtain necessary drawings.

• Locate work areas using drawings or paperwork that specify airplane and section numbers.

• Verify kitted parts against installation plans and bill of materials to ensure they are correct and free of defects.

• Obtain parts from the Parts Control Area if they are not pre-picked, ensuring they meet specifications.

• Drill, ream, and countersink holes in parts/assemblies per specifications, using appropriate tools.

• Disassemble parts and deburr holes to prepare for fastener installation.

• Use solvents to clean surfaces prior to sealing or assembly, and apply sealants, alodine, primers, adhesives, and special finishes as required.

• Install cable control pulleys and rig control cables according to drawings and specifications.

• Check and adjust actuator motors for full travel of flight control systems using power sources and hand tools.

• Clean the work area and ensure the removal of Foreign Object Debris (FOD) and submit completed jobs or in-process checks to inspectors as required.

• Physical Demands and Potential Hazards:

• Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs.

• Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting.

• Work in environments that may involve contact with metals, solvents, and coolants.

• Operate in proximity to moving parts and tools, sharp cutters, and potential slipping hazards.

• Adapt to varying noise levels and atmospheric conditions.

• Utilize personal safety gear to protect face/eyes, hands/arms, and feet while performing job duties.

This position is expected to be 100% onsite. The selected candidate will be required to work onsite at one of the listed location options.

This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. “US Person” includes US Citizen, lawful permanent resident, refugee, or asylee.

Current Boeing employees working in Puget Sound must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool. Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

Basic Qualifications:

• Experience using hand tools and/or hand-held power tools

• Experience working with safety and quality processes and procedures.

• Basic Computer experience and competency.

• Ability to walk constantly throughout the workday; stand 6-8 hours per day; climb or work from stairs/steps up to 8 hours per day; climb ladders; bend and twist frequently up to six hours per day; squat and kneel.

• A ble to perform work at heights up to 50 feet above ground level with appropriate safety gear.

Preferred Qualifications:

• Experience reading and interpreting drawings, specifications,

• material processes, schematic and diagrams

• Attended a Boeing partnered manufacturing related high school or

• Preferred community and technology college academic program

Typical Education & Experience:

High school graduate or GED preferred.

Relocation:

• Relocation assistance is not a negotiable benefit for this position. Candidates must live in the immediate area or relocate at their own expense.

Drug Free Workplace:

Boeing is a Drug Free Workplace where post offer applicants and employees are subject to testing for marijuana, cocaine, opioids, amphetamines, PCP, and alcohol when criteria is met as outlined in our policies.

Union Representation Statement:

This is an hourly position governed by the International Association of Machinists (IAM-751) Collective Bargaining agreement.

Shift Work Statement :  

• This position is for a variety of shifts   

Total Rewards & Pay Transparency:

At Boeing, we strive to deliver a Total Rewards package that will attract, engage and retain the top talent. Elements of the Total Rewards package include competitive base pay and variable compensation opportunities.

The Boeing Company also provides eligible employees with an opportunity to enroll in a variety of benefit programs, generally including health insurance, flexible spending accounts, health savings accounts, retirement savings plans, life and disability insurance programs, and a number of programs that provide for both paid and unpaid time away from work.

The specific programs and options available to any given employee may vary depending on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.

Pay is based upon candidate experience and qualifications, as well as market and business considerations.

Summary pay range: $24.32 – $53.30

Applications for this position will be accepted until Sept. 04, 2026

Language Requirements

English Preferred

Relocation

Relocation assistance is not a negotiable benefit for this position.

Visa Sponsorship

Employer will not sponsor applicants for employment visa status.

Shift

This position is for variable shift

Equal Opportunity Employer:

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.